fishing wire from second floor to garage in first floor
I was trying to drill a 1” hole on the horizontal beam in the wall to fish cable from second floor to garage in first floor. After drilling about 12 inch deep, I cannot go further anymore. Here is few pics about the hole and the wall structure, as well as the drill bit. Please let me know what is going on or if you have any better ideas. Thanks
]1[
]2[
]3
wiring walls
asked Jan 27 at 1:28
JasperJasper
285
add a comment |
I was trying to drill a 1” hole on the horizontal beam in the wall to fish cable from second floor to garage in first floor. After drilling about 12 inch deep, I cannot go further anymore. Here is few pics about the hole and the wall structure, as well as the drill bit. Please let me know what is going on or if you have any better ideas. Thanks]1[]2[]3
wiring walls
asked Jan 27 at 1:28
JasperJasper
285
add a comment |
I was trying to drill a 1” hole on the horizontal beam in the wall to fish cable from second floor to garage in first floor. After drilling about 12 inch deep, I cannot go further anymore. Here is few pics about the hole and the wall structure, as well as the drill bit. Please let me know what is going on or if you have any better ideas. Thanks]1[]2[]3
wiring walls
asked Jan 27 at 1:28
JasperJasper
285
I was trying to drill a 1” hole on the horizontal beam in the wall to fish cable from second floor to garage in first floor. After drilling about 12 inch deep, I cannot go further anymore. Here is few pics about the hole and the wall structure, as well as the drill bit. Please let me know what is going on or if you have any better ideas. Thanks]1[]2[]3
wiring walls
wiring walls
asked Jan 27 at 1:28
JasperJasper
285
asked Jan 27 at 1:28
JasperJasper
285
asked Jan 27 at 1:28
JasperJasper
285
asked Jan 27 at 1:28
JasperJasper
285
asked Jan 27 at 1:28
JasperJasper
285
285
add a comment |
add a comment |
2 Answers
2
active
oldest
votes
I think that using a spade type of bit there will be really tough going. I would use a regular twist bit. Possibly two if it is really tough going - e.g., 1/2" first and then followup with a 1" through the 1/2" starter hole.
If you have access to do so, it may be easier to drill from the bottom up than from the top down because the hole will empty itself thanks to gravity.
answered Jan 27 at 1:58
manassehkatzmanassehkatz
9,1021335
1
Drilling from bottom really makes sense. I should have done it that way. I tried to remove the wood dust from the hole by adapting a smaller pipe to my vacuum. I then tried to drill further and I finally made through.
– Jasper
Jan 28 at 6:17
add a comment |
You can purchase really long standard twist bits and they also sell flexible ones that allow you to have the drill outside of the cavity. You then bend it into a hole in the floor plate.
I'd drill a smaller one using one of these bits, and assuming that goes well, look to make it larger, perhaps from the bottom.
Obviously make sure there's nothing below you that wouldn't like being drilled into.
answered Jan 27 at 5:09
NormanNorman
1163
Yes using smaller flexible to do pilot drilling first is quite useful. I'd do this next time if I ever need to.
– Jasper
Jan 28 at 6:19
add a comment |
Your Answer
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "73"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f155955%2ffishing-wire-from-second-floor-to-garage-in-first-floor%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
2 Answers
2
active
oldest
votes
2 Answers
2
active
oldest
votes
active
oldest
votes
active
oldest
votes
I think that using a spade type of bit there will be really tough going. I would use a regular twist bit. Possibly two if it is really tough going - e.g., 1/2" first and then followup with a 1" through the 1/2" starter hole.
If you have access to do so, it may be easier to drill from the bottom up than from the top down because the hole will empty itself thanks to gravity.
answered Jan 27 at 1:58
manassehkatzmanassehkatz
9,1021335
1
Drilling from bottom really makes sense. I should have done it that way. I tried to remove the wood dust from the hole by adapting a smaller pipe to my vacuum. I then tried to drill further and I finally made through.
– Jasper
Jan 28 at 6:17
add a comment |
I think that using a spade type of bit there will be really tough going. I would use a regular twist bit. Possibly two if it is really tough going - e.g., 1/2" first and then followup with a 1" through the 1/2" starter hole.
If you have access to do so, it may be easier to drill from the bottom up than from the top down because the hole will empty itself thanks to gravity.
answered Jan 27 at 1:58
manassehkatzmanassehkatz
9,1021335
1
Drilling from bottom really makes sense. I should have done it that way. I tried to remove the wood dust from the hole by adapting a smaller pipe to my vacuum. I then tried to drill further and I finally made through.
– Jasper
Jan 28 at 6:17
add a comment |
I think that using a spade type of bit there will be really tough going. I would use a regular twist bit. Possibly two if it is really tough going - e.g., 1/2" first and then followup with a 1" through the 1/2" starter hole.
If you have access to do so, it may be easier to drill from the bottom up than from the top down because the hole will empty itself thanks to gravity.
answered Jan 27 at 1:58
manassehkatzmanassehkatz
9,1021335
I think that using a spade type of bit there will be really tough going. I would use a regular twist bit. Possibly two if it is really tough going - e.g., 1/2" first and then followup with a 1" through the 1/2" starter hole.
If you have access to do so, it may be easier to drill from the bottom up than from the top down because the hole will empty itself thanks to gravity.
answered Jan 27 at 1:58
manassehkatzmanassehkatz
9,1021335
answered Jan 27 at 1:58
manassehkatzmanassehkatz
9,1021335
answered Jan 27 at 1:58
manassehkatzmanassehkatz
9,1021335
answered Jan 27 at 1:58
manassehkatzmanassehkatz
9,1021335
9,1021335
1
Drilling from bottom really makes sense. I should have done it that way. I tried to remove the wood dust from the hole by adapting a smaller pipe to my vacuum. I then tried to drill further and I finally made through.
– Jasper
Jan 28 at 6:17
add a comment |
1
Drilling from bottom really makes sense. I should have done it that way. I tried to remove the wood dust from the hole by adapting a smaller pipe to my vacuum. I then tried to drill further and I finally made through.
– Jasper
Jan 28 at 6:17
1
1
Drilling from bottom really makes sense. I should have done it that way. I tried to remove the wood dust from the hole by adapting a smaller pipe to my vacuum. I then tried to drill further and I finally made through.
– Jasper
Jan 28 at 6:17
Drilling from bottom really makes sense. I should have done it that way. I tried to remove the wood dust from the hole by adapting a smaller pipe to my vacuum. I then tried to drill further and I finally made through.
– Jasper
Jan 28 at 6:17
add a comment |
You can purchase really long standard twist bits and they also sell flexible ones that allow you to have the drill outside of the cavity. You then bend it into a hole in the floor plate.
I'd drill a smaller one using one of these bits, and assuming that goes well, look to make it larger, perhaps from the bottom.
Obviously make sure there's nothing below you that wouldn't like being drilled into.
answered Jan 27 at 5:09
NormanNorman
1163
Yes using smaller flexible to do pilot drilling first is quite useful. I'd do this next time if I ever need to.
– Jasper
Jan 28 at 6:19
add a comment |
You can purchase really long standard twist bits and they also sell flexible ones that allow you to have the drill outside of the cavity. You then bend it into a hole in the floor plate.
I'd drill a smaller one using one of these bits, and assuming that goes well, look to make it larger, perhaps from the bottom.
Obviously make sure there's nothing below you that wouldn't like being drilled into.
answered Jan 27 at 5:09
NormanNorman
1163
Yes using smaller flexible to do pilot drilling first is quite useful. I'd do this next time if I ever need to.
– Jasper
Jan 28 at 6:19
add a comment |
You can purchase really long standard twist bits and they also sell flexible ones that allow you to have the drill outside of the cavity. You then bend it into a hole in the floor plate.
I'd drill a smaller one using one of these bits, and assuming that goes well, look to make it larger, perhaps from the bottom.
Obviously make sure there's nothing below you that wouldn't like being drilled into.
answered Jan 27 at 5:09
NormanNorman
1163
You can purchase really long standard twist bits and they also sell flexible ones that allow you to have the drill outside of the cavity. You then bend it into a hole in the floor plate.
I'd drill a smaller one using one of these bits, and assuming that goes well, look to make it larger, perhaps from the bottom.
Obviously make sure there's nothing below you that wouldn't like being drilled into.
answered Jan 27 at 5:09
NormanNorman
1163
answered Jan 27 at 5:09
NormanNorman
1163
answered Jan 27 at 5:09
NormanNorman
1163
answered Jan 27 at 5:09
NormanNorman
1163
1163
Yes using smaller flexible to do pilot drilling first is quite useful. I'd do this next time if I ever need to.
– Jasper
Jan 28 at 6:19
add a comment |
Yes using smaller flexible to do pilot drilling first is quite useful. I'd do this next time if I ever need to.
– Jasper
Jan 28 at 6:19
Yes using smaller flexible to do pilot drilling first is quite useful. I'd do this next time if I ever need to.
– Jasper
Jan 28 at 6:19
Yes using smaller flexible to do pilot drilling first is quite useful. I'd do this next time if I ever need to.
– Jasper
Jan 28 at 6:19
add a comment |
Thanks for contributing an answer to Home Improvement Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f155955%2ffishing-wire-from-second-floor-to-garage-in-first-floor%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
