Is PETG filament food safe?
$begingroup$
I've been trying to find a 3D printer filament which would not release any chemicals if in contact with heated water for a substantial amount of time. So far, I've easily ruled out both PLA and ABS, as they're not considered food safe from what I can find. I have found PETG filament, which seems to be food safe.
My question is: "Is there's anything special you'd have to do to make sure the print is food safe, or as in my case, to make sure it's safe for usage in a mug?".
I will be using a steel extruder as brass ones may contain lead.
filament safety food petg
edited Feb 9 at 20:24
Trish
6,53121343
asked Feb 9 at 14:23
MelvinMelvin
132
$endgroup$
add a comment |
$begingroup$
I've been trying to find a 3D printer filament which would not release any chemicals if in contact with heated water for a substantial amount of time. So far, I've easily ruled out both PLA and ABS, as they're not considered food safe from what I can find. I have found PETG filament, which seems to be food safe.
My question is: "Is there's anything special you'd have to do to make sure the print is food safe, or as in my case, to make sure it's safe for usage in a mug?".
I will be using a steel extruder as brass ones may contain lead.
filament safety food petg
edited Feb 9 at 20:24
Trish
6,53121343
asked Feb 9 at 14:23
MelvinMelvin
132
$endgroup$
$begingroup$
Welcome to 3dPrinting.SE! I'm not quite sure your question is on topic for the site, but have a look at this article. I think it answers your questions. They actually suggest using PLA, because it is non-toxic. You have to seal it, though, as using it straight from the print bed is going to leave you seeping "stuff" all over the place (prints are very commonly porous). Anyway, there are others who are far more adept at this than I am who can give you a real answer.
$endgroup$
– Pᴀᴜʟsᴛᴇʀ2
Feb 9 at 14:50
$begingroup$
@Pᴀᴜʟsᴛᴇʀ2 although that article also says that PETG is a good filament
$endgroup$
– Melvin
Feb 9 at 14:56
$begingroup$
All I was suggesting is that don't discard PLA as an option, mainly because it is non-toxic due to it being made from corn starch.
$endgroup$
– Pᴀᴜʟsᴛᴇʀ2
Feb 9 at 15:13
$begingroup$
@Pᴀᴜʟsᴛᴇʀ2 Ok thanks :)
$endgroup$
– Melvin
Feb 9 at 15:14
1
$begingroup$
it's the tiny gaps that breed pathogens that causes 3d prints not to be food-safe, not the chemicals in the filament (although that could also be a concern).
$endgroup$
– dandavis
Feb 11 at 22:52
add a comment |
$begingroup$
I've been trying to find a 3D printer filament which would not release any chemicals if in contact with heated water for a substantial amount of time. So far, I've easily ruled out both PLA and ABS, as they're not considered food safe from what I can find. I have found PETG filament, which seems to be food safe.
My question is: "Is there's anything special you'd have to do to make sure the print is food safe, or as in my case, to make sure it's safe for usage in a mug?".
I will be using a steel extruder as brass ones may contain lead.
filament safety food petg
edited Feb 9 at 20:24
Trish
6,53121343
asked Feb 9 at 14:23
MelvinMelvin
132
$endgroup$
I've been trying to find a 3D printer filament which would not release any chemicals if in contact with heated water for a substantial amount of time. So far, I've easily ruled out both PLA and ABS, as they're not considered food safe from what I can find. I have found PETG filament, which seems to be food safe.
My question is: "Is there's anything special you'd have to do to make sure the print is food safe, or as in my case, to make sure it's safe for usage in a mug?".
I will be using a steel extruder as brass ones may contain lead.
filament safety food petg
filament safety food petg
edited Feb 9 at 20:24
Trish
6,53121343
asked Feb 9 at 14:23
MelvinMelvin
132
edited Feb 9 at 20:24
Trish
6,53121343
asked Feb 9 at 14:23
MelvinMelvin
132
edited Feb 9 at 20:24
Trish
6,53121343
edited Feb 9 at 20:24
Trish
6,53121343
edited Feb 9 at 20:24
Trish
6,53121343
6,53121343
asked Feb 9 at 14:23
MelvinMelvin
132
asked Feb 9 at 14:23
MelvinMelvin
132
asked Feb 9 at 14:23
MelvinMelvin
132
132
$begingroup$
Welcome to 3dPrinting.SE! I'm not quite sure your question is on topic for the site, but have a look at this article. I think it answers your questions. They actually suggest using PLA, because it is non-toxic. You have to seal it, though, as using it straight from the print bed is going to leave you seeping "stuff" all over the place (prints are very commonly porous). Anyway, there are others who are far more adept at this than I am who can give you a real answer.
$endgroup$
– Pᴀᴜʟsᴛᴇʀ2
Feb 9 at 14:50
$begingroup$
@Pᴀᴜʟsᴛᴇʀ2 although that article also says that PETG is a good filament
$endgroup$
– Melvin
Feb 9 at 14:56
$begingroup$
All I was suggesting is that don't discard PLA as an option, mainly because it is non-toxic due to it being made from corn starch.
$endgroup$
– Pᴀᴜʟsᴛᴇʀ2
Feb 9 at 15:13
$begingroup$
@Pᴀᴜʟsᴛᴇʀ2 Ok thanks :)
$endgroup$
– Melvin
Feb 9 at 15:14
1
$begingroup$
it's the tiny gaps that breed pathogens that causes 3d prints not to be food-safe, not the chemicals in the filament (although that could also be a concern).
$endgroup$
– dandavis
Feb 11 at 22:52
add a comment |
$begingroup$
Welcome to 3dPrinting.SE! I'm not quite sure your question is on topic for the site, but have a look at this article. I think it answers your questions. They actually suggest using PLA, because it is non-toxic. You have to seal it, though, as using it straight from the print bed is going to leave you seeping "stuff" all over the place (prints are very commonly porous). Anyway, there are others who are far more adept at this than I am who can give you a real answer.
$endgroup$
– Pᴀᴜʟsᴛᴇʀ2
Feb 9 at 14:50
$begingroup$
@Pᴀᴜʟsᴛᴇʀ2 although that article also says that PETG is a good filament
$endgroup$
– Melvin
Feb 9 at 14:56
$begingroup$
All I was suggesting is that don't discard PLA as an option, mainly because it is non-toxic due to it being made from corn starch.
$endgroup$
– Pᴀᴜʟsᴛᴇʀ2
Feb 9 at 15:13
$begingroup$
@Pᴀᴜʟsᴛᴇʀ2 Ok thanks :)
$endgroup$
– Melvin
Feb 9 at 15:14
1
$begingroup$
it's the tiny gaps that breed pathogens that causes 3d prints not to be food-safe, not the chemicals in the filament (although that could also be a concern).
$endgroup$
– dandavis
Feb 11 at 22:52
$begingroup$
Welcome to 3dPrinting.SE! I'm not quite sure your question is on topic for the site, but have a look at this article. I think it answers your questions. They actually suggest using PLA, because it is non-toxic. You have to seal it, though, as using it straight from the print bed is going to leave you seeping "stuff" all over the place (prints are very commonly porous). Anyway, there are others who are far more adept at this than I am who can give you a real answer.
$endgroup$
– Pᴀᴜʟsᴛᴇʀ2
Feb 9 at 14:50
$begingroup$
Welcome to 3dPrinting.SE! I'm not quite sure your question is on topic for the site, but have a look at this article. I think it answers your questions. They actually suggest using PLA, because it is non-toxic. You have to seal it, though, as using it straight from the print bed is going to leave you seeping "stuff" all over the place (prints are very commonly porous). Anyway, there are others who are far more adept at this than I am who can give you a real answer.
$endgroup$
– Pᴀᴜʟsᴛᴇʀ2
Feb 9 at 14:50
$begingroup$
@Pᴀᴜʟsᴛᴇʀ2 although that article also says that PETG is a good filament
$endgroup$
– Melvin
Feb 9 at 14:56
$begingroup$
@Pᴀᴜʟsᴛᴇʀ2 although that article also says that PETG is a good filament
$endgroup$
– Melvin
Feb 9 at 14:56
$begingroup$
All I was suggesting is that don't discard PLA as an option, mainly because it is non-toxic due to it being made from corn starch.
$endgroup$
– Pᴀᴜʟsᴛᴇʀ2
Feb 9 at 15:13
$begingroup$
All I was suggesting is that don't discard PLA as an option, mainly because it is non-toxic due to it being made from corn starch.
$endgroup$
– Pᴀᴜʟsᴛᴇʀ2
Feb 9 at 15:13
$begingroup$
@Pᴀᴜʟsᴛᴇʀ2 Ok thanks :)
$endgroup$
– Melvin
Feb 9 at 15:14
$begingroup$
@Pᴀᴜʟsᴛᴇʀ2 Ok thanks :)
$endgroup$
– Melvin
Feb 9 at 15:14
1
1
$begingroup$
it's the tiny gaps that breed pathogens that causes 3d prints not to be food-safe, not the chemicals in the filament (although that could also be a concern).
$endgroup$
– dandavis
Feb 11 at 22:52
$begingroup$
it's the tiny gaps that breed pathogens that causes 3d prints not to be food-safe, not the chemicals in the filament (although that could also be a concern).
$endgroup$
– dandavis
Feb 11 at 22:52
add a comment |
2 Answers
2
active
oldest
votes
$begingroup$
Many manufactures list their filaments as being food safe, but I would not treat this as "gospel truth". Apparently, the FDA considers PETG to be safe for food contact, but they are probably thinking about injection-moulded and vacuum-formed parts. Unfortunately, an initial search of the FDA's website did not yield any definitive information.
Even if a particular filament is genuinely food safe, that does not mean that a 3D-printed part made from it will be food safe, since there will be an abundance of nooks and crannies where bacteria can lodge and reproduce. You would have to sterilise a utensil before and after every use to be absolutely safe.
Anyway, good luck with making a water-tight mug with an FDM printer. You will probably have to seal it to make it water-tight, and then it will be the food-safety of the sealant that you will need to worry about. I would give it a miss, if I were you (at least, for other people's use). Items intended for one-time use would be OK, I suppose.
answered Feb 9 at 15:29
MickMick
1,498315
$endgroup$
1
$begingroup$
Yeah, thanks, just realized I could just buy a normal mug and take it apart, as that will make my life a lot easier :)
$endgroup$
– Melvin
Feb 9 at 16:48
$begingroup$
This print is watertight: youtube.com/watch?v=OzfXVH59LjM
$endgroup$
– FarO
Feb 14 at 19:07
add a comment |
$begingroup$
As far as PET-based filaments go, most of them are FDA approved. So yes, "food safe". It's the process of 3D printing that ruins that. all the little layers trap just about everything and are hard to clean. If you wanted to boil your part, that might work, but you'd be better off buying a food-safe coating spray for your parts.
answered Mar 4 at 22:39
Levi GiesbrechtLevi Giesbrecht
113
$endgroup$
$begingroup$
Much of the information is simply false. PETG filament exists but PET is not printable in itself. Also, while PETG in itself is a food rated material, this does not make either the filament or the printed object food rated as the manufacturing procedures have to be food rated also.
$endgroup$
– Trish
Mar 5 at 1:22
add a comment |
Your Answer
StackExchange.ifUsing("editor", function () {
return StackExchange.using("mathjaxEditing", function () {
StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix) {
StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["$", "$"], ["\\(","\\)"]]);
});
});
}, "mathjax-editing");
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "640"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2f3dprinting.stackexchange.com%2fquestions%2f8210%2fis-petg-filament-food-safe%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
2 Answers
2
active
oldest
votes
2 Answers
2
active
oldest
votes
active
oldest
votes
active
oldest
votes
$begingroup$
Many manufactures list their filaments as being food safe, but I would not treat this as "gospel truth". Apparently, the FDA considers PETG to be safe for food contact, but they are probably thinking about injection-moulded and vacuum-formed parts. Unfortunately, an initial search of the FDA's website did not yield any definitive information.
Even if a particular filament is genuinely food safe, that does not mean that a 3D-printed part made from it will be food safe, since there will be an abundance of nooks and crannies where bacteria can lodge and reproduce. You would have to sterilise a utensil before and after every use to be absolutely safe.
Anyway, good luck with making a water-tight mug with an FDM printer. You will probably have to seal it to make it water-tight, and then it will be the food-safety of the sealant that you will need to worry about. I would give it a miss, if I were you (at least, for other people's use). Items intended for one-time use would be OK, I suppose.
answered Feb 9 at 15:29
MickMick
1,498315
$endgroup$
1
$begingroup$
Yeah, thanks, just realized I could just buy a normal mug and take it apart, as that will make my life a lot easier :)
$endgroup$
– Melvin
Feb 9 at 16:48
$begingroup$
This print is watertight: youtube.com/watch?v=OzfXVH59LjM
$endgroup$
– FarO
Feb 14 at 19:07
add a comment |
$begingroup$
Many manufactures list their filaments as being food safe, but I would not treat this as "gospel truth". Apparently, the FDA considers PETG to be safe for food contact, but they are probably thinking about injection-moulded and vacuum-formed parts. Unfortunately, an initial search of the FDA's website did not yield any definitive information.
Even if a particular filament is genuinely food safe, that does not mean that a 3D-printed part made from it will be food safe, since there will be an abundance of nooks and crannies where bacteria can lodge and reproduce. You would have to sterilise a utensil before and after every use to be absolutely safe.
Anyway, good luck with making a water-tight mug with an FDM printer. You will probably have to seal it to make it water-tight, and then it will be the food-safety of the sealant that you will need to worry about. I would give it a miss, if I were you (at least, for other people's use). Items intended for one-time use would be OK, I suppose.
answered Feb 9 at 15:29
MickMick
1,498315
$endgroup$
1
$begingroup$
Yeah, thanks, just realized I could just buy a normal mug and take it apart, as that will make my life a lot easier :)
$endgroup$
– Melvin
Feb 9 at 16:48
$begingroup$
This print is watertight: youtube.com/watch?v=OzfXVH59LjM
$endgroup$
– FarO
Feb 14 at 19:07
add a comment |
$begingroup$
Many manufactures list their filaments as being food safe, but I would not treat this as "gospel truth". Apparently, the FDA considers PETG to be safe for food contact, but they are probably thinking about injection-moulded and vacuum-formed parts. Unfortunately, an initial search of the FDA's website did not yield any definitive information.
Even if a particular filament is genuinely food safe, that does not mean that a 3D-printed part made from it will be food safe, since there will be an abundance of nooks and crannies where bacteria can lodge and reproduce. You would have to sterilise a utensil before and after every use to be absolutely safe.
Anyway, good luck with making a water-tight mug with an FDM printer. You will probably have to seal it to make it water-tight, and then it will be the food-safety of the sealant that you will need to worry about. I would give it a miss, if I were you (at least, for other people's use). Items intended for one-time use would be OK, I suppose.
answered Feb 9 at 15:29
MickMick
1,498315
$endgroup$
Many manufactures list their filaments as being food safe, but I would not treat this as "gospel truth". Apparently, the FDA considers PETG to be safe for food contact, but they are probably thinking about injection-moulded and vacuum-formed parts. Unfortunately, an initial search of the FDA's website did not yield any definitive information.
Even if a particular filament is genuinely food safe, that does not mean that a 3D-printed part made from it will be food safe, since there will be an abundance of nooks and crannies where bacteria can lodge and reproduce. You would have to sterilise a utensil before and after every use to be absolutely safe.
Anyway, good luck with making a water-tight mug with an FDM printer. You will probably have to seal it to make it water-tight, and then it will be the food-safety of the sealant that you will need to worry about. I would give it a miss, if I were you (at least, for other people's use). Items intended for one-time use would be OK, I suppose.
answered Feb 9 at 15:29
MickMick
1,498315
edited Feb 10 at 12:30
answered Feb 9 at 15:29
MickMick
1,498315
answered Feb 9 at 15:29
MickMick
1,498315
answered Feb 9 at 15:29
MickMick
1,498315
1,498315
1
$begingroup$
Yeah, thanks, just realized I could just buy a normal mug and take it apart, as that will make my life a lot easier :)
$endgroup$
– Melvin
Feb 9 at 16:48
$begingroup$
This print is watertight: youtube.com/watch?v=OzfXVH59LjM
$endgroup$
– FarO
Feb 14 at 19:07
add a comment |
1
$begingroup$
Yeah, thanks, just realized I could just buy a normal mug and take it apart, as that will make my life a lot easier :)
$endgroup$
– Melvin
Feb 9 at 16:48
$begingroup$
This print is watertight: youtube.com/watch?v=OzfXVH59LjM
$endgroup$
– FarO
Feb 14 at 19:07
1
1
$begingroup$
Yeah, thanks, just realized I could just buy a normal mug and take it apart, as that will make my life a lot easier :)
$endgroup$
– Melvin
Feb 9 at 16:48
$begingroup$
Yeah, thanks, just realized I could just buy a normal mug and take it apart, as that will make my life a lot easier :)
$endgroup$
– Melvin
Feb 9 at 16:48
$begingroup$
This print is watertight: youtube.com/watch?v=OzfXVH59LjM
$endgroup$
– FarO
Feb 14 at 19:07
$begingroup$
This print is watertight: youtube.com/watch?v=OzfXVH59LjM
$endgroup$
– FarO
Feb 14 at 19:07
add a comment |
$begingroup$
As far as PET-based filaments go, most of them are FDA approved. So yes, "food safe". It's the process of 3D printing that ruins that. all the little layers trap just about everything and are hard to clean. If you wanted to boil your part, that might work, but you'd be better off buying a food-safe coating spray for your parts.
answered Mar 4 at 22:39
Levi GiesbrechtLevi Giesbrecht
113
$endgroup$
$begingroup$
Much of the information is simply false. PETG filament exists but PET is not printable in itself. Also, while PETG in itself is a food rated material, this does not make either the filament or the printed object food rated as the manufacturing procedures have to be food rated also.
$endgroup$
– Trish
Mar 5 at 1:22
add a comment |
$begingroup$
As far as PET-based filaments go, most of them are FDA approved. So yes, "food safe". It's the process of 3D printing that ruins that. all the little layers trap just about everything and are hard to clean. If you wanted to boil your part, that might work, but you'd be better off buying a food-safe coating spray for your parts.
answered Mar 4 at 22:39
Levi GiesbrechtLevi Giesbrecht
113
$endgroup$
$begingroup$
Much of the information is simply false. PETG filament exists but PET is not printable in itself. Also, while PETG in itself is a food rated material, this does not make either the filament or the printed object food rated as the manufacturing procedures have to be food rated also.
$endgroup$
– Trish
Mar 5 at 1:22
add a comment |
$begingroup$
As far as PET-based filaments go, most of them are FDA approved. So yes, "food safe". It's the process of 3D printing that ruins that. all the little layers trap just about everything and are hard to clean. If you wanted to boil your part, that might work, but you'd be better off buying a food-safe coating spray for your parts.
answered Mar 4 at 22:39
Levi GiesbrechtLevi Giesbrecht
113
$endgroup$
As far as PET-based filaments go, most of them are FDA approved. So yes, "food safe". It's the process of 3D printing that ruins that. all the little layers trap just about everything and are hard to clean. If you wanted to boil your part, that might work, but you'd be better off buying a food-safe coating spray for your parts.
answered Mar 4 at 22:39
Levi GiesbrechtLevi Giesbrecht
113
edited Mar 6 at 4:45
answered Mar 4 at 22:39
Levi GiesbrechtLevi Giesbrecht
113
answered Mar 4 at 22:39
Levi GiesbrechtLevi Giesbrecht
113
answered Mar 4 at 22:39
Levi GiesbrechtLevi Giesbrecht
113
113
$begingroup$
Much of the information is simply false. PETG filament exists but PET is not printable in itself. Also, while PETG in itself is a food rated material, this does not make either the filament or the printed object food rated as the manufacturing procedures have to be food rated also.
$endgroup$
– Trish
Mar 5 at 1:22
add a comment |
$begingroup$
Much of the information is simply false. PETG filament exists but PET is not printable in itself. Also, while PETG in itself is a food rated material, this does not make either the filament or the printed object food rated as the manufacturing procedures have to be food rated also.
$endgroup$
– Trish
Mar 5 at 1:22
$begingroup$
Much of the information is simply false. PETG filament exists but PET is not printable in itself. Also, while PETG in itself is a food rated material, this does not make either the filament or the printed object food rated as the manufacturing procedures have to be food rated also.
$endgroup$
– Trish
Mar 5 at 1:22
$begingroup$
Much of the information is simply false. PETG filament exists but PET is not printable in itself. Also, while PETG in itself is a food rated material, this does not make either the filament or the printed object food rated as the manufacturing procedures have to be food rated also.
$endgroup$
– Trish
Mar 5 at 1:22
add a comment |
Thanks for contributing an answer to 3D Printing Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
Use MathJax to format equations. MathJax reference.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2f3dprinting.stackexchange.com%2fquestions%2f8210%2fis-petg-filament-food-safe%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
$begingroup$
Welcome to 3dPrinting.SE! I'm not quite sure your question is on topic for the site, but have a look at this article. I think it answers your questions. They actually suggest using PLA, because it is non-toxic. You have to seal it, though, as using it straight from the print bed is going to leave you seeping "stuff" all over the place (prints are very commonly porous). Anyway, there are others who are far more adept at this than I am who can give you a real answer.
$endgroup$
– Pᴀᴜʟsᴛᴇʀ2
Feb 9 at 14:50
$begingroup$
@Pᴀᴜʟsᴛᴇʀ2 although that article also says that PETG is a good filament
$endgroup$
– Melvin
Feb 9 at 14:56
$begingroup$
All I was suggesting is that don't discard PLA as an option, mainly because it is non-toxic due to it being made from corn starch.
$endgroup$
– Pᴀᴜʟsᴛᴇʀ2
Feb 9 at 15:13
$begingroup$
@Pᴀᴜʟsᴛᴇʀ2 Ok thanks :)
$endgroup$
– Melvin
Feb 9 at 15:14
1
$begingroup$
it's the tiny gaps that breed pathogens that causes 3d prints not to be food-safe, not the chemicals in the filament (although that could also be a concern).
$endgroup$
– dandavis
Feb 11 at 22:52