How to push an endoscopic camera upto 20 meters in a horizontal pipe?












3














I have a small endoscopic camera (custom made). I wanted to push the camera inside a horizontal pipe of dimensions varying from (25 mm to 65 mm ID). But the wire attached to the camera is not stiff enough to push the camera. After a certain length, camera stops moving (cz the wire coils inside the pipe). But I have seen Companies like Olympus etc., push their camera even up to 25 meters. I know that they have a special cover over the wire which is stiff and flexible for pushing the camera. How can I make a cover similar to that ? I have enquired many places but could not find a solution. Thanks in advance for your help.










share|improve this question







New contributor




user18754 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.




















  • Why not pull it...
    – Solar Mike
    yesterday










  • @SolarMike: Well, you'd need a way to get a thread or something across from one end of the pipe to the "pulling end".
    – Wasabi
    yesterday






  • 2




    @Wasabi - That's easy, you just need a properly trained ferret ;)
    – alephzero
    yesterday










  • @Wasabi sometimes it is worth thinking « from the other end »...And I have used "pull-throughs" that are used to drag stuff through a long section and you also bring through another "pull-through" for the next time ... depends what the pipe is used for though...
    – Solar Mike
    yesterday












  • You have not specified how thick the cable is that trails behind the camera. Thus, we have no idea how much clearance remains for whatever additional thing is pushing the camera from the 25 mm to 65 mm ID that you've mentioned. What does the profile of the 25 mm to 65 mm ID variation look like as the camera travels along the horizontal pipe? For instance, is it 65mm for X m, then abruptly 25mm? Does it taper smoothly from 65mm to 25mm? Is the pipe straight? Does the solution have to accommodate bends in the pipe?
    – Makyen
    yesterday


















3














I have a small endoscopic camera (custom made). I wanted to push the camera inside a horizontal pipe of dimensions varying from (25 mm to 65 mm ID). But the wire attached to the camera is not stiff enough to push the camera. After a certain length, camera stops moving (cz the wire coils inside the pipe). But I have seen Companies like Olympus etc., push their camera even up to 25 meters. I know that they have a special cover over the wire which is stiff and flexible for pushing the camera. How can I make a cover similar to that ? I have enquired many places but could not find a solution. Thanks in advance for your help.










share|improve this question







New contributor




user18754 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.




















  • Why not pull it...
    – Solar Mike
    yesterday










  • @SolarMike: Well, you'd need a way to get a thread or something across from one end of the pipe to the "pulling end".
    – Wasabi
    yesterday






  • 2




    @Wasabi - That's easy, you just need a properly trained ferret ;)
    – alephzero
    yesterday










  • @Wasabi sometimes it is worth thinking « from the other end »...And I have used "pull-throughs" that are used to drag stuff through a long section and you also bring through another "pull-through" for the next time ... depends what the pipe is used for though...
    – Solar Mike
    yesterday












  • You have not specified how thick the cable is that trails behind the camera. Thus, we have no idea how much clearance remains for whatever additional thing is pushing the camera from the 25 mm to 65 mm ID that you've mentioned. What does the profile of the 25 mm to 65 mm ID variation look like as the camera travels along the horizontal pipe? For instance, is it 65mm for X m, then abruptly 25mm? Does it taper smoothly from 65mm to 25mm? Is the pipe straight? Does the solution have to accommodate bends in the pipe?
    – Makyen
    yesterday
















3












3








3







I have a small endoscopic camera (custom made). I wanted to push the camera inside a horizontal pipe of dimensions varying from (25 mm to 65 mm ID). But the wire attached to the camera is not stiff enough to push the camera. After a certain length, camera stops moving (cz the wire coils inside the pipe). But I have seen Companies like Olympus etc., push their camera even up to 25 meters. I know that they have a special cover over the wire which is stiff and flexible for pushing the camera. How can I make a cover similar to that ? I have enquired many places but could not find a solution. Thanks in advance for your help.










share|improve this question







New contributor




user18754 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.











I have a small endoscopic camera (custom made). I wanted to push the camera inside a horizontal pipe of dimensions varying from (25 mm to 65 mm ID). But the wire attached to the camera is not stiff enough to push the camera. After a certain length, camera stops moving (cz the wire coils inside the pipe). But I have seen Companies like Olympus etc., push their camera even up to 25 meters. I know that they have a special cover over the wire which is stiff and flexible for pushing the camera. How can I make a cover similar to that ? I have enquired many places but could not find a solution. Thanks in advance for your help.







materials springs






share|improve this question







New contributor




user18754 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.











share|improve this question







New contributor




user18754 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.









share|improve this question




share|improve this question






New contributor




user18754 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.









asked yesterday









user18754

161




161




New contributor




user18754 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.





New contributor





user18754 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.






user18754 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.












  • Why not pull it...
    – Solar Mike
    yesterday










  • @SolarMike: Well, you'd need a way to get a thread or something across from one end of the pipe to the "pulling end".
    – Wasabi
    yesterday






  • 2




    @Wasabi - That's easy, you just need a properly trained ferret ;)
    – alephzero
    yesterday










  • @Wasabi sometimes it is worth thinking « from the other end »...And I have used "pull-throughs" that are used to drag stuff through a long section and you also bring through another "pull-through" for the next time ... depends what the pipe is used for though...
    – Solar Mike
    yesterday












  • You have not specified how thick the cable is that trails behind the camera. Thus, we have no idea how much clearance remains for whatever additional thing is pushing the camera from the 25 mm to 65 mm ID that you've mentioned. What does the profile of the 25 mm to 65 mm ID variation look like as the camera travels along the horizontal pipe? For instance, is it 65mm for X m, then abruptly 25mm? Does it taper smoothly from 65mm to 25mm? Is the pipe straight? Does the solution have to accommodate bends in the pipe?
    – Makyen
    yesterday




















  • Why not pull it...
    – Solar Mike
    yesterday










  • @SolarMike: Well, you'd need a way to get a thread or something across from one end of the pipe to the "pulling end".
    – Wasabi
    yesterday






  • 2




    @Wasabi - That's easy, you just need a properly trained ferret ;)
    – alephzero
    yesterday










  • @Wasabi sometimes it is worth thinking « from the other end »...And I have used "pull-throughs" that are used to drag stuff through a long section and you also bring through another "pull-through" for the next time ... depends what the pipe is used for though...
    – Solar Mike
    yesterday












  • You have not specified how thick the cable is that trails behind the camera. Thus, we have no idea how much clearance remains for whatever additional thing is pushing the camera from the 25 mm to 65 mm ID that you've mentioned. What does the profile of the 25 mm to 65 mm ID variation look like as the camera travels along the horizontal pipe? For instance, is it 65mm for X m, then abruptly 25mm? Does it taper smoothly from 65mm to 25mm? Is the pipe straight? Does the solution have to accommodate bends in the pipe?
    – Makyen
    yesterday


















Why not pull it...
– Solar Mike
yesterday




Why not pull it...
– Solar Mike
yesterday












@SolarMike: Well, you'd need a way to get a thread or something across from one end of the pipe to the "pulling end".
– Wasabi
yesterday




@SolarMike: Well, you'd need a way to get a thread or something across from one end of the pipe to the "pulling end".
– Wasabi
yesterday




2




2




@Wasabi - That's easy, you just need a properly trained ferret ;)
– alephzero
yesterday




@Wasabi - That's easy, you just need a properly trained ferret ;)
– alephzero
yesterday












@Wasabi sometimes it is worth thinking « from the other end »...And I have used "pull-throughs" that are used to drag stuff through a long section and you also bring through another "pull-through" for the next time ... depends what the pipe is used for though...
– Solar Mike
yesterday






@Wasabi sometimes it is worth thinking « from the other end »...And I have used "pull-throughs" that are used to drag stuff through a long section and you also bring through another "pull-through" for the next time ... depends what the pipe is used for though...
– Solar Mike
yesterday














You have not specified how thick the cable is that trails behind the camera. Thus, we have no idea how much clearance remains for whatever additional thing is pushing the camera from the 25 mm to 65 mm ID that you've mentioned. What does the profile of the 25 mm to 65 mm ID variation look like as the camera travels along the horizontal pipe? For instance, is it 65mm for X m, then abruptly 25mm? Does it taper smoothly from 65mm to 25mm? Is the pipe straight? Does the solution have to accommodate bends in the pipe?
– Makyen
yesterday






You have not specified how thick the cable is that trails behind the camera. Thus, we have no idea how much clearance remains for whatever additional thing is pushing the camera from the 25 mm to 65 mm ID that you've mentioned. What does the profile of the 25 mm to 65 mm ID variation look like as the camera travels along the horizontal pipe? For instance, is it 65mm for X m, then abruptly 25mm? Does it taper smoothly from 65mm to 25mm? Is the pipe straight? Does the solution have to accommodate bends in the pipe?
– Makyen
yesterday












3 Answers
3






active

oldest

votes


















3














You can buy endoscope or borescope cables which should "just work," though 20m is longer than the typical cable you will find on Amazon or Ebay.



If you want to try making your own, look at the design of Bowden cables (used for brake cables on bikes, etc). The outer cover is made like a coil spring, so it can bend around a large radius but won't "buckle" into a small radius at one point.



You might also consider flexible chimney sweeping rods, which are made in 1 or 2 meter lengths which you can join together as you move the camera down the pipe. They would have the disadvantage that the camera cable would be separate from the rods, unlike a Bowden cable where it would be inside the cable and protected from dirt and damage.



In fact chimney sweeping suppliers sell inspection cameras that fit onto standard sweeping rods, and are self contained with battery power and a wireless data transmission link, so you don't need a separate cable to the camera.






share|improve this answer































    2














    Most electrical engineers use an electrician Conduit Ducting wire for that (which you could use in your cable setup), but in your case it probably easier to use a piece of string and a vacuum cleaner. Put the vacuum cleaner at one end and suck the piece of string through. Then pull the camera through using the string like explained in How to get cables in a long pipe - with vacuum cleaner






    share|improve this answer










    New contributor




    Rolf Huisman is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
    Check out our Code of Conduct.


















    • Similar to oil industry : Make a "pig" , flexible foam plastic/rubber to fit pipe. Attach the camera to the pig and blow it down your pipe. Do your exam as you slowly pull the camera/ pig back. The industry does this for many miles.
      – blacksmith37
      yesterday



















    0














    I think I have a very similar USB camera.



    I tape it to an electrician's tool called, in trade jargon, fish tape, this is a narrow strong, springy tape, which is uses to pull the wires through conduits.



    My sewer line is prone to clogging at the point when it connects to old City sewer main, which even though is public, has never been serviced by the city because it runs in my property, (easement).



    I have taped a keychain led flash light to this fish tape and it helps a lot.






    share|improve this answer





















      Your Answer





      StackExchange.ifUsing("editor", function () {
      return StackExchange.using("mathjaxEditing", function () {
      StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix) {
      StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["$", "$"], ["\\(","\\)"]]);
      });
      });
      }, "mathjax-editing");

      StackExchange.ready(function() {
      var channelOptions = {
      tags: "".split(" "),
      id: "595"
      };
      initTagRenderer("".split(" "), "".split(" "), channelOptions);

      StackExchange.using("externalEditor", function() {
      // Have to fire editor after snippets, if snippets enabled
      if (StackExchange.settings.snippets.snippetsEnabled) {
      StackExchange.using("snippets", function() {
      createEditor();
      });
      }
      else {
      createEditor();
      }
      });

      function createEditor() {
      StackExchange.prepareEditor({
      heartbeatType: 'answer',
      autoActivateHeartbeat: false,
      convertImagesToLinks: false,
      noModals: true,
      showLowRepImageUploadWarning: true,
      reputationToPostImages: null,
      bindNavPrevention: true,
      postfix: "",
      imageUploader: {
      brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
      contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
      allowUrls: true
      },
      noCode: true, onDemand: true,
      discardSelector: ".discard-answer"
      ,immediatelyShowMarkdownHelp:true
      });


      }
      });






      user18754 is a new contributor. Be nice, and check out our Code of Conduct.










      draft saved

      draft discarded


















      StackExchange.ready(
      function () {
      StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fengineering.stackexchange.com%2fquestions%2f25250%2fhow-to-push-an-endoscopic-camera-upto-20-meters-in-a-horizontal-pipe%23new-answer', 'question_page');
      }
      );

      Post as a guest















      Required, but never shown

























      3 Answers
      3






      active

      oldest

      votes








      3 Answers
      3






      active

      oldest

      votes









      active

      oldest

      votes






      active

      oldest

      votes









      3














      You can buy endoscope or borescope cables which should "just work," though 20m is longer than the typical cable you will find on Amazon or Ebay.



      If you want to try making your own, look at the design of Bowden cables (used for brake cables on bikes, etc). The outer cover is made like a coil spring, so it can bend around a large radius but won't "buckle" into a small radius at one point.



      You might also consider flexible chimney sweeping rods, which are made in 1 or 2 meter lengths which you can join together as you move the camera down the pipe. They would have the disadvantage that the camera cable would be separate from the rods, unlike a Bowden cable where it would be inside the cable and protected from dirt and damage.



      In fact chimney sweeping suppliers sell inspection cameras that fit onto standard sweeping rods, and are self contained with battery power and a wireless data transmission link, so you don't need a separate cable to the camera.






      share|improve this answer




























        3














        You can buy endoscope or borescope cables which should "just work," though 20m is longer than the typical cable you will find on Amazon or Ebay.



        If you want to try making your own, look at the design of Bowden cables (used for brake cables on bikes, etc). The outer cover is made like a coil spring, so it can bend around a large radius but won't "buckle" into a small radius at one point.



        You might also consider flexible chimney sweeping rods, which are made in 1 or 2 meter lengths which you can join together as you move the camera down the pipe. They would have the disadvantage that the camera cable would be separate from the rods, unlike a Bowden cable where it would be inside the cable and protected from dirt and damage.



        In fact chimney sweeping suppliers sell inspection cameras that fit onto standard sweeping rods, and are self contained with battery power and a wireless data transmission link, so you don't need a separate cable to the camera.






        share|improve this answer


























          3












          3








          3






          You can buy endoscope or borescope cables which should "just work," though 20m is longer than the typical cable you will find on Amazon or Ebay.



          If you want to try making your own, look at the design of Bowden cables (used for brake cables on bikes, etc). The outer cover is made like a coil spring, so it can bend around a large radius but won't "buckle" into a small radius at one point.



          You might also consider flexible chimney sweeping rods, which are made in 1 or 2 meter lengths which you can join together as you move the camera down the pipe. They would have the disadvantage that the camera cable would be separate from the rods, unlike a Bowden cable where it would be inside the cable and protected from dirt and damage.



          In fact chimney sweeping suppliers sell inspection cameras that fit onto standard sweeping rods, and are self contained with battery power and a wireless data transmission link, so you don't need a separate cable to the camera.






          share|improve this answer














          You can buy endoscope or borescope cables which should "just work," though 20m is longer than the typical cable you will find on Amazon or Ebay.



          If you want to try making your own, look at the design of Bowden cables (used for brake cables on bikes, etc). The outer cover is made like a coil spring, so it can bend around a large radius but won't "buckle" into a small radius at one point.



          You might also consider flexible chimney sweeping rods, which are made in 1 or 2 meter lengths which you can join together as you move the camera down the pipe. They would have the disadvantage that the camera cable would be separate from the rods, unlike a Bowden cable where it would be inside the cable and protected from dirt and damage.



          In fact chimney sweeping suppliers sell inspection cameras that fit onto standard sweeping rods, and are self contained with battery power and a wireless data transmission link, so you don't need a separate cable to the camera.







          share|improve this answer














          share|improve this answer



          share|improve this answer








          edited yesterday

























          answered yesterday









          alephzero

          7,1021521




          7,1021521























              2














              Most electrical engineers use an electrician Conduit Ducting wire for that (which you could use in your cable setup), but in your case it probably easier to use a piece of string and a vacuum cleaner. Put the vacuum cleaner at one end and suck the piece of string through. Then pull the camera through using the string like explained in How to get cables in a long pipe - with vacuum cleaner






              share|improve this answer










              New contributor




              Rolf Huisman is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
              Check out our Code of Conduct.


















              • Similar to oil industry : Make a "pig" , flexible foam plastic/rubber to fit pipe. Attach the camera to the pig and blow it down your pipe. Do your exam as you slowly pull the camera/ pig back. The industry does this for many miles.
                – blacksmith37
                yesterday
















              2














              Most electrical engineers use an electrician Conduit Ducting wire for that (which you could use in your cable setup), but in your case it probably easier to use a piece of string and a vacuum cleaner. Put the vacuum cleaner at one end and suck the piece of string through. Then pull the camera through using the string like explained in How to get cables in a long pipe - with vacuum cleaner






              share|improve this answer










              New contributor




              Rolf Huisman is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
              Check out our Code of Conduct.


















              • Similar to oil industry : Make a "pig" , flexible foam plastic/rubber to fit pipe. Attach the camera to the pig and blow it down your pipe. Do your exam as you slowly pull the camera/ pig back. The industry does this for many miles.
                – blacksmith37
                yesterday














              2












              2








              2






              Most electrical engineers use an electrician Conduit Ducting wire for that (which you could use in your cable setup), but in your case it probably easier to use a piece of string and a vacuum cleaner. Put the vacuum cleaner at one end and suck the piece of string through. Then pull the camera through using the string like explained in How to get cables in a long pipe - with vacuum cleaner






              share|improve this answer










              New contributor




              Rolf Huisman is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
              Check out our Code of Conduct.









              Most electrical engineers use an electrician Conduit Ducting wire for that (which you could use in your cable setup), but in your case it probably easier to use a piece of string and a vacuum cleaner. Put the vacuum cleaner at one end and suck the piece of string through. Then pull the camera through using the string like explained in How to get cables in a long pipe - with vacuum cleaner







              share|improve this answer










              New contributor




              Rolf Huisman is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
              Check out our Code of Conduct.









              share|improve this answer



              share|improve this answer








              edited yesterday









              user8055

              550317




              550317






              New contributor




              Rolf Huisman is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
              Check out our Code of Conduct.









              answered yesterday









              Rolf Huisman

              1213




              1213




              New contributor




              Rolf Huisman is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
              Check out our Code of Conduct.





              New contributor





              Rolf Huisman is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
              Check out our Code of Conduct.






              Rolf Huisman is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
              Check out our Code of Conduct.












              • Similar to oil industry : Make a "pig" , flexible foam plastic/rubber to fit pipe. Attach the camera to the pig and blow it down your pipe. Do your exam as you slowly pull the camera/ pig back. The industry does this for many miles.
                – blacksmith37
                yesterday


















              • Similar to oil industry : Make a "pig" , flexible foam plastic/rubber to fit pipe. Attach the camera to the pig and blow it down your pipe. Do your exam as you slowly pull the camera/ pig back. The industry does this for many miles.
                – blacksmith37
                yesterday
















              Similar to oil industry : Make a "pig" , flexible foam plastic/rubber to fit pipe. Attach the camera to the pig and blow it down your pipe. Do your exam as you slowly pull the camera/ pig back. The industry does this for many miles.
              – blacksmith37
              yesterday




              Similar to oil industry : Make a "pig" , flexible foam plastic/rubber to fit pipe. Attach the camera to the pig and blow it down your pipe. Do your exam as you slowly pull the camera/ pig back. The industry does this for many miles.
              – blacksmith37
              yesterday











              0














              I think I have a very similar USB camera.



              I tape it to an electrician's tool called, in trade jargon, fish tape, this is a narrow strong, springy tape, which is uses to pull the wires through conduits.



              My sewer line is prone to clogging at the point when it connects to old City sewer main, which even though is public, has never been serviced by the city because it runs in my property, (easement).



              I have taped a keychain led flash light to this fish tape and it helps a lot.






              share|improve this answer


























                0














                I think I have a very similar USB camera.



                I tape it to an electrician's tool called, in trade jargon, fish tape, this is a narrow strong, springy tape, which is uses to pull the wires through conduits.



                My sewer line is prone to clogging at the point when it connects to old City sewer main, which even though is public, has never been serviced by the city because it runs in my property, (easement).



                I have taped a keychain led flash light to this fish tape and it helps a lot.






                share|improve this answer
























                  0












                  0








                  0






                  I think I have a very similar USB camera.



                  I tape it to an electrician's tool called, in trade jargon, fish tape, this is a narrow strong, springy tape, which is uses to pull the wires through conduits.



                  My sewer line is prone to clogging at the point when it connects to old City sewer main, which even though is public, has never been serviced by the city because it runs in my property, (easement).



                  I have taped a keychain led flash light to this fish tape and it helps a lot.






                  share|improve this answer












                  I think I have a very similar USB camera.



                  I tape it to an electrician's tool called, in trade jargon, fish tape, this is a narrow strong, springy tape, which is uses to pull the wires through conduits.



                  My sewer line is prone to clogging at the point when it connects to old City sewer main, which even though is public, has never been serviced by the city because it runs in my property, (easement).



                  I have taped a keychain led flash light to this fish tape and it helps a lot.







                  share|improve this answer












                  share|improve this answer



                  share|improve this answer










                  answered yesterday









                  kamran

                  3,4841410




                  3,4841410






















                      user18754 is a new contributor. Be nice, and check out our Code of Conduct.










                      draft saved

                      draft discarded


















                      user18754 is a new contributor. Be nice, and check out our Code of Conduct.













                      user18754 is a new contributor. Be nice, and check out our Code of Conduct.












                      user18754 is a new contributor. Be nice, and check out our Code of Conduct.
















                      Thanks for contributing an answer to Engineering Stack Exchange!


                      • Please be sure to answer the question. Provide details and share your research!

                      But avoid



                      • Asking for help, clarification, or responding to other answers.

                      • Making statements based on opinion; back them up with references or personal experience.


                      Use MathJax to format equations. MathJax reference.


                      To learn more, see our tips on writing great answers.





                      Some of your past answers have not been well-received, and you're in danger of being blocked from answering.


                      Please pay close attention to the following guidance:


                      • Please be sure to answer the question. Provide details and share your research!

                      But avoid



                      • Asking for help, clarification, or responding to other answers.

                      • Making statements based on opinion; back them up with references or personal experience.


                      To learn more, see our tips on writing great answers.




                      draft saved


                      draft discarded














                      StackExchange.ready(
                      function () {
                      StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fengineering.stackexchange.com%2fquestions%2f25250%2fhow-to-push-an-endoscopic-camera-upto-20-meters-in-a-horizontal-pipe%23new-answer', 'question_page');
                      }
                      );

                      Post as a guest















                      Required, but never shown





















































                      Required, but never shown














                      Required, but never shown












                      Required, but never shown







                      Required, but never shown

































                      Required, but never shown














                      Required, but never shown












                      Required, but never shown







                      Required, but never shown







                      Popular posts from this blog

                      Human spaceflight

                      Can not write log (Is /dev/pts mounted?) - openpty in Ubuntu-on-Windows?

                      張江高科駅